压缩行程的英文

发音:

英文翻译
造句

combustion stroke
combustionstroke
compression cycle
compression travel
compressionstroke
instroke
pressure stroke
scavenging-compression stroke

压缩 compress; condense; reduce; ...
行程 route or distance of travel; ...
压缩行程阀 compression valve
换气压缩行程 exchange-compression stroke; expansion-exchange stroke
弹簧缓冲压缩行程 spring buffer stroke
悬架的压缩行程 compression stroke of suspension
车轮上跳（减振器压缩行程） jounce
内缩行程 inward stroke; retract stroke; retraction stroke
伸缩行程 travel plunger
收缩行程 prestroke; retraction stroke
引缩行程 plunger travel
压缩行程时弹簧动弯曲限止器 bump stop
压缩行为 compression behavior; compression behaviour
油缸杆回缩行程的拉力 cylinder pull
压缩膨胀行程 compression-and-power stroke
紧缩行 row merger
缩行式 indended style
压缩机活塞的行程容积 displacement of compressor
行程 1.(路程) route or distance of travel; distance of run; length of travel; distance travelled; journey; flight 艰难的行程 hard journey; 漫长的行程 long route; 行程五千多公里 travel over 5,000 kilometres; 一小时的行程 an hour's march; 这将是一整天的行程。it will make a full day's march.2.[机械工程] stroke; throw; travel 活塞行程 piston travel; 滑枕行程 ram stroke3.[电学] range
退缩行为 withdrawal behavior
压缩 compress; condense; reduce; cut down; compression; contraction; compaction; pack; reduction; recompression; hoop (静水压的) 压缩非生产性开支 cut down non-productive expenses; 压缩国内需求 depress [lowering] domestic demand; 压缩机关团体购买力 limiting government institutions' purchase of consumer goods; 压缩不适当进口 reduce inappropriate imports; 压缩一则新闻报道 condense a news story; 压缩比 compression ratio; ratio of compression; 压缩饼干 ship biscuit; pilot bread; hardtack; 压缩成型机 compacting shape machine; 压缩冲程 [机械工程] compression stroke; 压缩处理 compressing; 压缩点火 compressed ignition; [机械工程] compression ignition; 压缩制冷 compression refrigeration; 压缩制冷机 compression refrigerating machine; 压缩作用 compression
衰老性退缩行为 aging regression behavior
行程长度，行程 run length
半行程 half trip
泵行程 pump stroke; throw of pump

"查查词典"手机版

千万人都在用的超大词汇词典翻译APP

例句与用法

Exchange - compression stroke
换气压缩行程
It was found that the compression speed and compression stroke are the two factors affecting the molding pressure most significantly
由模拟找出了压缩速度与压缩行程是两个影响成型压力极大的因素。
It was found that the compression speed and compression stroke are the two factors affecting the molding pressure most significantly
由仿真找出了压缩速度与压缩行程是两个影响成型压力极大的因素。
Using lower switch time , lower compression speed and higher compression stroke will result in lower cavity pressures
使用较短的切换时间、较低的压缩速度以及较高的压缩行程将产生较低的模安穴压力。
When the engine runs in compression stroke and power stroke , the valves must close tightly on their seats to produce a gas - tight seal and thus prevent the gases escaping from the combustion chamber
当发动机处于压缩行程和做功行程时，阀门必须紧紧地关闭以产生一个不透气的气封，以防止气体逃离燃烧室。
The controller of magnetorheological semi - active suspension system was consisted of drive current control subsystem of magnetorheological damper and mechanical structural fuzzy control subsystem of vehicle , the unsymmetry damping force relation of suspension compress travel and promote travel is solved with coefficient of language - value of damper force output variable
由汽车结构振动模糊控制子系统和磁流变阻尼器驱动电流控制子系统构建了磁流变半主动悬架控制器，用模糊集语言赋值系数反映了悬架伸张行程和压缩行程不对称阻尼控制力的关系。
Simulation and the associated numerical algorithm on the injection - compression molding ( icm ) process were developed to understand processing characteristics by changing processing parameters including compression speed , switch time from injection to compression , compression stroke as well as initial cavity thickness and part thickness using disk parts
摘要射出压缩成型的仿真以及数值运算是要了解成型参数的改变，包括：压缩速度、射出与封装的切换时间、压缩行程等制程特性而创建的，同时也包含了初始的开模厚度以及使用在光盘片的成品厚度。
Simulation and the associated numerical algorithm on the injection - compression molding ( icm ) process were developed to understand processing characteristics by changing processing parameters including compression speed , switch time from injection to compression , compression stroke as well as initial cavity thickness and part thickness using disk parts
摘要射出压缩成型的模拟以及数值运算是要了解成型参数的改变，包括：压缩速度、射出与压缩的切换时间、压缩行程等制程特性而建立的，同时也包含了初始的开模厚度以及使用在光碟片的成品厚度。