linewidth中文什么意思

例句与用法

更多例句：  上一页    下一页
1. It is shown that the divergence angle of pumping beam and off axis pumping and spontaneous radiation influenced the linewidth of parametric light more quickly than those of other factors did , and the linewidth of parametric light is very narrow far away from the degeneracy point , and the linewidth begins to large quickly at the degeneracy point
   结果表明，泵浦光的发散角、泵浦光的偏轴泵浦、自发辐射对参量光的线宽影响较大。在远离简并点处，线宽较小，在简并点处，线宽较大。
2. With the development of laser techniques , the optical cavity has played an important role on monitoring laser mode , measurement and narrowing of laser linewidth , laser mode cleaner , laser frequency stabilization , optical spectrum and cavity - qed etc . , due to its advantages of ultra - low losses , high finesse and narrow linewidth
   随着激光技术的发展，谐振腔由于其腔内损耗小、精细度高、线宽窄等特点，使得其在监视激光模式、测量并压窄激光线宽、激光模式清洁、激光稳频、激光光谱学、腔量子电动力学等方面起到重要的作用。
3. Based on these foundations , we give a perfect scheme of the bbo opos : single pass amplification coefficient of the opg under different pump intensity is calculated ; collinear type - i and type - ii phase matching tuning curve pumped by the q switch nd : yag various harmonics as well as noncollinear type - i tuning curve are calculated in details ; the effect of the walkoff for the nonlinear effect coefficient and the group velocity matching are analyzed ; the acceptance angle in parametric process is calculated ; the numerical threshold of the bbo opo is calculated ; the process of the saturation and depletion of the pump beam are analyzed ; the relationship of the conversion efficiency and reflectance of output mirror are discussed ; various linewidth controlling methods are discussed ; the improvement of the beam quality applying the unstable cavity is discussed ; and the crystal bbo design is considered
   在此基础上，给出了一整套bbo - opo激光参数设计方案：计算了不同泵浦强度下的参量放大倍数；详细计算了在nd : yag调q激光器各次谐波泵浦条件下的共线类和类相位匹配的调谐曲线，以及非共线类相位匹配调谐曲线；分析了走离角对非线性系数和群速匹配的影响；计算了参量过程的允许角；计算了bbo - opo的理论阈值条件；分析了饱和与泵浦光束的消耗过程；给出了转换效率与超过泵浦阈值的倍数的关系；讨论了转换效率与输出镜反射率的关系；讨论了线宽控制的各种方法；研究了利用非稳腔改善光束质量的方法；考虑了bbo晶体的设计。
4. In the section of fabricating technology , i first discuss the ion beam technology . through the analysis of the effects of each parameter on the surface smoothness , profile fidelity and linewidth resolution in the process of ion etching , the suitable angle of incident ion beam , ion energy , density of ion beam and time of etching are selected combining the actual status of the mask
   在制作工艺的研究方面，首先研究了离子束刻蚀技术，通过对离子束刻蚀过程中各个参数对刻蚀元件的表面光洁度、轮廓保真度和线宽分辨的影响分析，结合掩膜的实际情况选择出了合适的离子束入射角、离子能量、束流密度和刻蚀时间等参数。
5. Secondly , we propose and demonstrate experimentally a novel multi - wavelength erbium - doped fiber ring laser by using a mach - zehnder fiber interferometer and composite cavity . as a result , simultaneous multi - wavelength oscillations with narrow linewidth and equal wavelength span are obtained in room temperature . this device has advantageous of simple design fabrication and low cost et al
   进一步，我们设计了一种新颖的多波长掺铒光纤环形激光器，这种激光器是利用mach - zenhder ( m - z )光纤型干涉仪作为梳状滤波器，并且与复合腔共同选频，获得了窄线宽、等间隔的多波长同时输出，这种激光器具有在常温工作，结构简单，成本低等优点。